New
LilyGO T-Camera Plus S3 OV2640 - ESP32-S3
- Availability: Directly available from warehouse in Eindhoven
- SKU: 006441
€36.00
Ex Tax: €29.75
A development board based on an ESP32-S3 microcontroller which has various sensors, including a camera and microphone.
See the following page for more information: GitHub
Check the tab "Downloads" for more information and/or downloads.
Report this review.
Schematic: 006441_SCH_T-CameraPlus-S3_V1.1_20241109.pdf
Specifications
| General | |
| Brand | LilyGO TTGO |
| Manufacturer model/SKU | H703 |
| Model revision | V1.1 |
| Features | Battery charger Display Camera Microcontroller Touchscreen SD-card adapter Audio amplifier Microphone Speaker/buzzer Programmable button(s) |
| General physical appearance | |
| Main color | Black |
| Weight [g] | 29 |
| Dimension X [mm] | 68 |
| Dimension Y [mm] | 28 |
| Mounting options | Mounting hole(s) |
| Diameter mounting hole(s) [mm] | 2 |
| Form factor | Module (general) |
| General electrical properties | |
| Minimum supply voltage [V DC] | 5 |
| Maximum supply voltage [V DC] | 5 |
| Minimum IO-pin input voltage [V] | 3.3 |
| Maximum IO-pin input voltage [V] | 3.3 |
| IO-pin output voltage [V] | 3.3 |
| Maximum IO-pin source current [mA] | 40 |
| Maximum IO-pin sink current [mA] | 28 |
| MCU/SoC | |
| Manufacturer | Espressif |
| Chip series | ESP32-S3 |
| Maximum clock frequency [MHz] | 240 |
| Number of cores | 2 |
| Internal memory | |
| SRAM [KB] | 512 |
| PSRAM [MB] | 8 |
| Flash memory [MB] | 16 |
| EEPROM type | Emulated |
| Communication | |
| Hardware interface(s) | I2C I2S Native USB UART PWM ADC GPIO USB CDC |
| Number of IO-pins | 4 (of which 2 connected to I2C bus and not recommended for other use) |
| Maximum available hardware PWM channels | 2 |
| Maximum available analog input pins (ADC) | 2 |
| Maximum available analog output pins (DAC) | 0 |
| Maximum available hardware UART interfaces | 1 |
| Maximum available hardware I2C interfaces | 2 |
| Maximum available hardware SPI interfaces | 0 |
| USB to serial converter | Integrated into microcontroller |
| Supported SD card size | Micro SD |
| Wireless communication | |
| Interface(s) | Wi-Fi Bluetooth |
| Wi-Fi chip/SoC | ESP32-S3 |
| Wi-Fi frequency [GHz] | 2.4 |
| Bluetooth chip/SoC | ESP32-S3 |
| Bluetooth version | 5.0 |
| Supported Bluetooth standard(s) | LE |
| Display | |
| Type | TFT |
| Driver | ST7789V |
| Screen diagonal [inch] | 1.3 |
| Number of pixels long side | 240 |
| Number of pixels short side | 240 |
| Display shape | Square |
| Pixel colors | RGB |
| Touchscreen | |
| Touchscreen controller | CST816S |
| Touch type | Capacitive |
| Multi-touch support | No |
| Scanner/camera | |
| Type | Camera |
| Sensor(chip) | OV2640 |
| Lense type | Normal |
| Number of pixels long side | 1632 |
| Number of pixels short side | 1220 |
| IR filter | Adjustable |
| Sound sensor | |
| Sensor (chip(s)) | MSM261S4030H0R |
| Type | Microphone |
| Audio amplifier | |
| Amplifier chip | MAX98357 |
| Number of (normal) channels | 1 |
| Minimum speaker impedance per (normal) channel [Ω] | 4 |
| Maximum speaker impedance per (normal) channel [Ω] | 8 |
| Speaker | |
| Speaker type | Standard |
| Impedance [Ω] | 8 |
| Maximum nominal (RMS) power [W] | 0.7 |
| Battery circuit | |
| Battery charger chip/SoC | SY6970 |
| Supported battery chemistry | Li-ion Li-Po |
| Maximum charging voltage [V] | 4.2 |
| Maximum charging current [mA] | 1000 (recommended because of used components, chip can charge up to 5000mA) |
| Adjustable charging current | Yes (via I2C) |
| Protection circuit | No |
| Connectors | |
| Power supply connector(s) | USB-C female |
| IO-connector(s) | JST-SH (compatible) male USB-C female |
| Battery connector(s) | Molex Picoblade (compatible) male |
| Speaker connector(s) | Molex Picoblade (compatible) male |
| Wi-Fi/Bluetooth antenna connector | IPEX MHF 4 male |
| Package contents | |
| Package contents | 1x T-Camera Plus S3 1x Molex Picoblade battery cable 1x Speaker 1x Antenna |